Slip On Pipe Flanges ASME B16.5 Pipe Fittings

The connection method of A182 F11 socket flange is to insert the pipe into the socket of the flange, and then seal it with welding or use a sealing gasket. This connection method is relatively strong and can adapt to the thermal expansion and contraction of the pipe to a certain extent.

Socket Weld Half Couplings is utilised in various applications in order to provide a torque free sealing and a leak free connection. Socket weld coupling is a very short section of pipes with socket bore at both ends or one end, but both can afford high pressure of 3000#, 6000#, 9000#. The Socket Weld Half Coupling are often directly welded to the run pipe, to form a branch connection.

A182 F304 slip on flange include flanges, bolt holes and sealing surfaces. The flange is a flat ring structure with an outer diameter larger than the outer diameter of the pipe connected to it. The bolt holes are evenly distributed on the flange and are used to install bolts to connect two flanges.

It is used to insert the pipe into the inner hole of flange, as the flange inner diameter is little bigger than the pipe’s outer diameter, pipe and flange could be connected by lap welding at the top and bottom of the flange. The slip-on flange is a simple and excellent alternative to a weld neck as it does not have a weld bevel, and therefore allows the pipe to be adjusted in length relative to its position of the flange.

There are various material grade for ASTM A182 stainless steel flange: F304/304L/304H, 316/316L, 321, 310S, 317,347,904L， 1.4404, 1.4437.

These pipe flanges are attached by inserting the pipe into the socket end and applying fillet weld around the top. This allows for a smooth bore and better flow of the fluid or gas inside of the pipe. The connection with the pipe is done with 1 fillet weld, at the outside of the flange. But before welding, a space must be created between flange or fitting and pipe.

A flange can be defined as a method that helps in connecting pipes, valves, etc., to form a full piping system. There are six flange classes ranging from #150 to #2500. Governed by B 16.5 standards, the ASME B16. 5 Class 300 Flange provides a pressure capacity of 300Lb.

A182 F316‌ lap joint flange uses flanges, steel rings, etc. to put the flange on the pipe end, so that the flange can move on the pipe end. The steel ring or flange is used as a sealing surface, and the flange is used to press them tightly.

600LB SW flanges can socket with the flanges and then welded with the pipes.Large diameter flanges can be series A and series B.ASME B 16.47 A & B are standard for large diameter flanges.

The spectacle blind flange is named because its shape resembles the number “8”. One end is a blind and the other end is an iron ring. However, the diameter of the throttling ring is the same as the diameter of the pipe and does not play a throttling role. This design makes the spectacle blind flange uniquely flexible and practical in the pipeline system.

The slip-on flange is a simple and excellent alternative to a weld neck as it does not have a weld bevel, and therefore allows the pipe to be adjusted in length relative to its position of the flange. The bore of the slip on will give ample amount of space for the matching pipe.

P280GH weld neck flange refers to a flange connection method that uses P280GH material as the base material and forms one or more layers of P280GH material welding layers on the flange surface through the butt welding process to improve the flange’s high temperature resistance, high pressure resistance and corrosion resistance.

What is a Blind Flange,what about its specification and its advantages.

What is a WN Flange?and what about its specification

Stainless steel flange, also called SS flange, it means the material of flange is stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500.

Steel Pipe Elbow is the most common pipe fitting that changes the direction of the pipeline. It plays a important role in the piping system.

The slip-on flange is a simple and excellent alternative to a weld neck as it does not have a weld bevel, and therefore allows the pipe to be adjusted in length relative to its position of the flange. The bore of the slip on will give ample amount of space for the matching pipe.

l. Large diameter flat welding flange has less high-pressure suitability compared to its weld neck counterpart. The basic ring style is suitable for the occasion of low pressure. The butt weld category of the flange is known as a weld neck flange. It suits the occasion of high temperature and pressure as defined in the ASME B16.47 code. Large diameter flanges are widely popularized and used in the sewage treatment industry, wind power industry, chemical industry, and machinery industry.

Class 1500 SO flange Flanges have many pressures:CL300, CL600, CL900, CL1500, CL2500.Flanges have five face types:RF RTJ FF MF TG. Slip on flanges can slip on the pipes and welding with the pipes.

Stainless steel flange, also called SS flange, it means the material of flange is stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500.

What is a Spectacle Flange and what about its specification and advantages.

What is a SW flange and what about its specification.

Stainless steel flange is popular because stainless steel has great anti-corrosive function.Flanges can be many types:WN,SO,SW,THD,LAPJ,BL.These flanges use different connections to connect with the pipes.Shanghai Zhucheng is a high quality manufactory who can supply all types of flanges.

150 LB blind flange is a flange similar to plug.BL flanges are used to close the pipe system.ASTM A105 forged flange is carbon steel flange in American Matel Standard.

These pipe flanges are attached by inserting the pipe into the socket end and applying fillet weld around the top. This allows for a smooth bore and better flow of the fluid or gas inside of the pipe. The connection with the pipe is done with 1 fillet weld, at the outside of the flange. But before welding, a space must be created between flange or fitting and pipe.

It is generally used in non-corrosive, non-critical, moderate pressure services. Slip on flanges of Class 150 and Class 300 are most commonly seen in utility engineering. Similar to welding neck flange, the slip on flange conforming to ASME B16.5 may generally be furnished with three facing types: raised face (RF), flat face/ full face (FF), or ring type joint (RTJ).

The specification of ASTM A182 Forged Pipe Fittings includes forged fittings, stainless steel, rolled alloy, forged alloy, pipe flanges as well as high-temperature service. Later then forgings and hot working, it would be cooled down to a certain temperature before heat treatment.

ASTM A182 F304 600LB slip on flanges are very popular type of flanges because of the excellent functions and high pressure.ASME B16.47 Series A & B are American Standard for large dimension flanges.According to ASME B16.47 Series A& B,the smallest size of flanges is 22 in.

Description of THD flange,what about its specification and advantages.