ASME B16.9 Stainless Steel Butt Weld Cross Fittings

BW tees and reducers are the most used pipe fittings in the piping system.Tees can branch the flow in piping systems.Carbon steel pipe fittings are popular as the great functions and affordable functions.

When short radius elbows are used, the maximum working pressure should not exceed 0.8 times of long radius elbows of the same specification Miter elbows are usually used for large-size pipes with moderate conditions in low pressure (design pressure s2.0mpa), water and similar fluid media

Pipe crossing is used where four pipes intersect. The cross pipe may have one inlet and three outlets, or three inlets and one outlet. The diameter of the outlet and inlet can be the same or different.

There are two types of 90 deg elbows:LR (long radius),SR (short radius).45 deg eblows are also have wide applications,be attention,45 deg elbow only have LR type.Butt welded pipe fittings have the most large used range as it can be 1/2″ – 80″.

24in equal tee is belong to large dimension fittings.SCH 40 is a commonly used wall thickness for butt welded fittings.Pipe tees can be equal tee and reducing tee.These tees have same functions,the only difference is reducing tee can reduce the flow in piping system.

When the direction change angle of the single section of the miter elbow is greater than 45, it should not be used in the pipeline with toxic and combustible media, or in the pipeline subject to vibration, pressure pulsation and alternating load due to temperature change

What is a STEEL PIPE TE and what about its specification and advantages.

BW 90 degree elbow is the most commonly used type of elbows.There is also 45 deg elbow.These elbows have similar functions,the only difference is the 90 degree elbow can changes the direction in 90 deg while the 45 degree elbow can changes in 45deg.You could find the steel pipe elbow specifications in the connent below.

ASME B16.9 elbow means BW elbow.ASME B16.9 is an American Standard for Butt welded fittings,A234 WP22 is represnets BW Alloy pipe fittings. Elbows can be 90 deg and 45 deg to change the pipes in 90 degree or 45 degree.Sometimes the elbows can be 180 deg to satisfy the clinet’s demands.

Elbow is a commonly used connecting pipe fitting in plumbing installation, which is used for connecting pipe bends

LR 90 degree steel pipe elbow are installed between different lengths pipe or tubing. It helps to change direction at 90 degree, and is commonly used to connect hoses to pumps, deck drains and valve.

Steel pipe elbow is a key part in a pressure piping system used to change the fluid flow direction. It is used to connect two pipes with same or different nominal diameters, and to make the pipe and thus the fluid direction turn to a certain direction of 45 degree or 90 degree. This change in fluid flow direction adds pressure losses to the system due to impact, friction and re-acceleration.

Butt welded elbow is a pipe fitting which used welded connection to connect with the pipes in piping system.BW elbbows have two degrees to choose:90 deg elbow and 45 deg eblbow.These elbows have similar functions,the only difference is the 90 degree elbow can changes the direction in 90 deg while the 45 degree elbow can changes in 45deg.

Butt welded elbow is a commonly used pipe fitting,it can divided as two types:90 deg and 45 deg.These elbows have similar functions,the only difference is the 90 degree elbow can changes the direction in 90 deg while the 45 degree elbow can changes in 45deg.These are Shanghai Zhucheng Pipe Fittings Manufacturing Co Ltd’s steel pipe fittings packages to ensure that the products are not damaged during transportation.

90 deg short radius elbow is a special type only for BW 90 degree elbows.Stainless steel pipe fittings are popular because of the an-ti corrosive function.Stainless steel pipe fittings can used over 50 years.

Butt welded reducers can be concentric (COC) reducer and eccentric (ECC) reducer.These reducers have same functions,the only difference is the internal structure.There are the BW fittings specifications in the content below.

What is a 90 DEGREE LR ELBOW and what about its specification and advantages.

Elbow could be ranged from direction angle, connection types, length and radius, material types. As we know, according to fluid direction of the pipelines, elbow can be divided into different degrees, such as 45 degree, 90 degree,180 degree, which are most common degrees. Also there has 60 degree and 120 degree, for some special pipelines.

This kind of elbow is classified by angle, and 45 degree elbow and 180 elbow is also very popular. And steel pipe elbow is also available in 60 degree, 30 degree and other special angle according to practical needs.

BW cap is used to close the pipe system,the function is similar to plug.A234 WPB is a commonly used grade for carbon steel in American Standard.SCH 40S is represents a wall thickness of butt welded fittings.The commonly used wall thicknesses for BW fittings are SCH 40,SCH 80.

How to use a BW tee in a pipesystem,what about its specification and advantages.

The lap joint stub end is required when attach the lap-joint flange to the piping system. The stub end and lap-joint flange assembly are used mainly in piping systems that necessitate frequent dismantling for inspection or routine maintenance.

The function of a 45 Degree Long Radius Elbow is same as 90 degrees long and short elbow, but the measurement and dimensions are different to that of a 90 degree long and the short elbow.

180 deg elbow is not commonly used but indispensable pipe fitting.180 degree elbow can changes the pipe systems in 180 degree.Carbon and alloy steel pipe fittings always be chosen in many industries because of the great functions and reasonable price.

SS400 90 DEG elbow is used to transport flow in piping system.Butt welded fittings used welded connection to connect with the pipes to achieve the strong and premanent connection.

LR 90 degree steel pipe elbow are installed between different lengths pipe or tubing. It helps to change direction at 90 degree, and is commonly used to connect hoses to pumps, deck drains and valve.SR 90 degree elbow is the same as the pipe elbow mentioned above, but the diameter is shorter. Therefore, this kind of steel elbow is often used when space is not enough.

Pipe tees can be equal tee and reducing tee.These tees have same functions,the only difference is reducing tee can reduce the flow in piping system.ASME B16.9 is American Standard for butt welded fittings.

Concentric reducers provide an in-line conical transition between pressurized pipes of different diameters. It is cone-shaped, and is used when there is a shift in diameter between pipes. 

Concentric reducers are tapered and are used when the diameter between pipes changes. It can be axially shifted and externally reconfigured to offer more efficient reducer connection.